AR- Ersatzteile

   The SI Flatwire Spring for is an economical, easy upgrade to any .308 AR system. The flatwire spring increases service life of the platform, smooths out the shooting cycle, and greatly outlasts the stock spring. Increased bolt load, in addition to decreased compressing force increases reliability in cycling. Product Specifications- OD: 0.94”- ID: 0.75”- Length: 19.5”- Rev: 42- Gauge (flat wire profile): 0.045” x 0.0935”- Weight: 3oz gross,2oz net The SI Flatwire Spring is an economical, and easy upgrade to any .308 AR system.  The flatwire spring increases service life of the platform, smooths out the shooting cycle, and greatly outlasts the stock spring.  Increased bolt load, in addition to decreased compressing force increases reliability in cycling.  Additionally, all SI Flatwire springs are cryogenically cycled to provide greater consistency, longer spring life, and greater resilience to high cyclic rates.  At a cost not much greater than stock carbine springs, the SI Flatwire is an easy option for those either looking to replace worn buffer springs or begin new builds.   Package include:- 1x Flatwire Spring for AR10/SR25/LR308Features- Cryo-cycled chrome-silicon steel for strength, reliability and longevity- Decreased harmonics lessens system vibration for faster follow up shots.- No more AR “twang”- Compatible with all standard AR10/SR25 receiver extension lengths

   High-quality Enhanced FIRING PIN, MIL-SPEC, Chrome Plated Designed for 7.62x39, compatible also with AR-15 Mil-Spec bolts in caliber 5.56 / .223 and .300 AAC Blackout ammo with hard primers. Every part manuactured is made to Military Specification and standards while also meeting with our own quality standards, passing through vigorous quality inspections through each phase of its journey to you, our customer.  100% AMERICAN MADE. 100% ANDERSON. 

  Armaspec High-End Custom Stainless Steel Lower Spare Parts Kit, made in the USA. The Kit contains common AR parts like springs and detents that are frequently lost or needed replacement. FEATURES:  Compatible with all AR-15 Mil-Spec Lower Receiver SPECIFICATIONS:  Material: Stainless Steel Finish: Polished Made in U.S.A COMPATIBILITY:  AR-Sector INCLUDES:  3 SS Takedown / Pivot Pin Detents 3 Takedown / Pivot Pin Detent Spring 1 SS Safety Selector Detent 1 Safety Selector Detent Spring 1 SS Buffer Retainer 1 Buffer Retainer Spring 1 SS Bolt Catch Detent 1 Bolt Catch Detent Spring 1 Magazine Release Spring

  Armaspec High-End Custom Buffer Retainer Kit FEATURES:  Machined from quality corrosion resistant stainless steel SPECIFICATIONS:  Finish: Polished COMPATIBILITY:  AR-15 & AR-10 INCLUDES:  1x Buffer Retainer 1x Buffer Retainer Spring MADE IN THE USA

  Armaspec Stainless Steel Anti-Walk pins are standard .154 sized pins. These pins are designed to keep your hammer/trigger pins from coming out. *Thread locker recommenced. FEATURES:  Stainless Steel Made in U.S.A COMPATIBILITY:  AR-15 and most AR-10 Fit NOT Heckler & Koch or Haenel models INCLUDES:  2 Armaspec Stainless steel Anti-Walk Pins / 2 Stainless Steel screws with Black Oxide finish / 2 Hex Keys MADE IN THE USA

  The Armaspec S3 Enhanced Trigger Guard Kit for combat applications. FEATURES:  Compatible with all AR-15 Mil-Spec Lower Receiver SPECIFICATIONS:  Material: Aluminum  Finish: Cerakoted  COMPATIBILITY:  AR-15 INCLUDES:  1x S3 Enhanced Trigger Guard 1x Trigger Guard Roll Pin 1x Set Screw 1x Hex Key  MADE IN THE USA

  The Armaspec S3 Enhanced Trigger Guard Kit for combat applications. FEATURES:  Compatible with all AR-15 Mil-Spec Lower Receiver SPECIFICATIONS:  Material: Aluminum  Finish: Anodized  COMPATIBILITY:  AR-15 INCLUDES:  1x S3 Enhanced Trigger Guard 1x Trigger Guard Roll Pin 1x Set Screw 1x Hex Key  MADE IN THE USA

  The Armaspec XPDW™ Gen2 stock is an aluminum 5 position stock with hardened steel rods. It incorporates a low profile lightweight aluminum latch carrier with a steel lock engagement point. The stock can be rapidly deployed using the ratcheting system or gravity by pointing the rifle up while disengaging the lock. The XPDW™ is designed to mount directly on your standard mil-spec buffer tube with no other modifications. It also features a QD butt attachment point for your sling, is made in the USA, and has a lifetime warranty. Pat. Pend.  FEATURES:  Ambidextrous 5-position stock adjustment  Attaches directly to Mil-Spec buffer tube: No special buffer or buffer tube needed  QD sling attachment point  SPECIFICATION:  Stock Weight: 14.29 oz.  Length:  Fully collapsed: 6.878"  Fully extended: 10"  Material: Aluminum  Finish: Mil-Spec FDE Cerakote COMPATIBILITY:  AR-15 AR-10 ONLY compatible with Carbine buffer tubes INCLUDES:  1x Armaspec XPDW Stock Assembly  1x Hex Wrench  1x Set Screw  MADE IN THE USA 

  The Armaspec XPDW™ Gen2 stock is an aluminum 5 position stock with hardened steel rods. It incorporates a low profile lightweight aluminum latch carrier with a steel lock engagement point. The stock can be rapidly deployed using the ratcheting system or gravity by pointing the rifle up while disengaging the lock. The XPDW™ is designed to mount directly on your standard mil-spec buffer tube with no other modifications. It also features a QD butt attachment point for your sling, is made in the USA, and has a lifetime warranty. Pat. Pend.  FEATURES:  Ambidextrous 5-position stock adjustment  Attaches directly to Mil-Spec buffer tube: No special buffer or buffer tube needed  QD sling attachment point  SPECIFICATION:  Stock Weight: 14.29 oz.  Length:  Fully collapsed: 6.878"  Fully extended: 10"  Material: Aluminum  Finish: Mil-Spec Type III Class 2 Hard Anodized Black  COMPATIBILITY:  AR-15 AR-10 ONLY compatible with Carbine buffer tubes INCLUDES:  1x Armaspec XPDW Stock Assembly  1x Hex Wrench  1x Set Screw  MADE IN THE USA

  The Armaspec B1 is an extended magazine release designed to extend the length of the factory button. The B1 makes it easier to release the magazine without changing the grip position. FEATURES: Compatible with BAD Lever and similar devices Large surface area for quick magazine reloads Easy to reach ergonomic design Release magazine without changing grip or position Serrated for positive depression and reduced slip Easy drop-in installation Compatible with most AR-15 and LR-308 receivers  SPECIFICATIONS:  Material: Aluminum Finish: Anodized or Cerakoted Weight: 0.18 oz.  COMPATIBILITY: AR-15 and AR-10 INCLUDES: 1x Extended Paddle 1x Magazine Release Button 2x Set Screws 1x Hex Key MADE IN THE USA

   The RSA QD provides a forward attachment point for the Magpul MS4® Sling and other push-button QD slings. Made from corrosion resistant steel, mounts on 1913 Picatinny rail, and places the attachment point at an angle optimized for comfortable two-point sling use while maintaining easy push-button access.  MADE IN THE USA

  When installed on the base of a 5.56x45 rifle magazine, the original Magpul provides improved speed and controllability during high stress, tactical magazine changes. Durable synthetic rubber loop with recessed rough gripping surface. Quick and easy installation and removal. Patented design based upon the tried-and-true para-cord loops and duct-tape tabs used by special warfare units worldwide. IMPROVED SPEED AND HANDLING Designed for use during high stress, tactical magazine changes. Improves speed of reload and control HIGHLY COMPATIBLE The Magpul fits most aluminum, steel, and polymer magazines Compatible accessories see under this article, accessories. TECHNICAL SPECIFICATIONS  Platform: AR15, M4, M16 Compatibility: Most aluminum, steel, and polymer 5.56 x 45 magazines MADE IN THE USA

  The Enhanced Ejection Port Cover is a drop-in upgrade designed to provide an improved installation process, physical strength, and corrosion resistance over the standard USGI ejection port cover. Compatible with AR15/M16/M4 MIL-SPEC AR15 upper receivers that accept USGI ejection port covers. Traditional stamped-steel ejection ports are malleable, prone to corrosion, and require tools to install. The Enhanced Ejection Port Cover snaps into place easily without having to remove your hand guard or barrel nut, wind any loose springs, or adjust small e-clips. Constructed of impact-resistant injection molded polymer, it is corrosion resistant and will not bend or deform from impacts.   EASIER THAN… EASY Installs easily in seconds Direct replacement for USGI ejection port cover MORE RUGGED THAN METAL PORT COVERS Durable, injection-molded polymer construction Corrosion resistant components Will not bend or deform from impacts MADE IN THE USA

  The Enhanced Ejection Port Cover is a drop-in upgrade designed to provide an improved installation process, physical strength, and corrosion resistance over the standard USGI ejection port cover. Compatible with AR15/M16/M4 MIL-SPEC AR15 upper receivers that accept USGI ejection port covers. Traditional stamped-steel ejection ports are malleable, prone to corrosion, and require tools to install. The Enhanced Ejection Port Cover snaps into place easily without having to remove your hand guard or barrel nut, wind any loose springs, or adjust small e-clips. Constructed of impact-resistant injection molded polymer, it is corrosion resistant and will not bend or deform from impacts. EASIER THAN… EASY Installs easily in seconds Direct replacement for USGI ejection port cover MORE RUGGED THAN METAL PORT COVERS Durable, injection-molded polymer construction Corrosion resistant components Will not bend or deform from impacts 

  The silencer-optimized Raptor-SD™ features a ported shaft designed to redirect gasses down and forward, away from the shooter’s face when shooting suppressed. Its ambidextrous design allows rapid palm "blading" or finger-thumb charging of the weapon, ensuring the motion is fluid and fast from either strong or support side. The Raptor-SD™ is compatible with most AR15/M16-pattern rifles Designed & Manufactured in the USA Machined from 7075-T6 aluminum MIL-SPEC Type 3 Hard Coat Anodized Finish  MADE IN THE USA

  Specifications: Compatible with ARMALITE AR-10A® and AR-10B® rifles only Compatible firearms see under this article, accessories MADE IN THE USA

  Specifications: Length: Carbine  Made from glasfiber reinforced polymer  Double heatshield MIL-STD  Easy installation No special tools are required to install the handguard Compatible with A2 Handguard Cap Compatible accessories, see accessories under this article MADE IN THE USA

  Original ArmaLite® M-15™/AR-15 Spring Replacement Kit, 20pcs Specifications: Compatible with M-15™/AR-15/M16/M4 rifles according to Mil-Spec diameters MADE IN THE USA

  Original ArmaLite® M-15™/AR-15 Field Repair Kit, 18pcs Specifications: Compatible with M-15™/AR-15/M16/M4 rifles according to Mil-Spec diameters MADE IN THE USA

  Original ArmaLite® M-15™/AR-15 Lower Parts Kit, 22pcs Specifications: Compatible with M-15™/AR-15/M16/M4 rifles according to Mil-Spec diameters MADE IN THE USA

  Fully adjustable Low-profile gas block for your AR-10® and AR-15/M-15™ rifle. Specifications: For AR-10® and AR-15/M-15™  Compatible with barrels utilizing a .750 gas block journal Laterally arranged adjustment screw, infinitely adjustable With front locking set screw Made from Stainless Steel Finish: SBN Included Roll Pin  Compatible accessories see under this article, accessories MADE IN THE USA

This Lower parts kit match perfectly with the GEN12 lower and is also compatible with most 308 DPMS gen1 patterned lowers. Kit includes as pictured: Hogue GripPistol grip screwSafety selector springSafety selector detentEnhanced Take Down/ Pivot pinsTake Down/ Pivot pin spring (2x)Take Down/ Pivot pin detent (2x)Safety SelectorAdaptive Tactical Ex-Performance StockBuffer Tube Milspec 308 Carbine (short 2.5") Buffer 3.8oz  308 Carbine SpringQD End PlateCastle NutBuffer RetainerBuffer Retainer SpringBeef-up kit Beef-up kit includes: Antiwalk trigger pins and screwsImproved Bolt Catch Enhanced Power Bolt Catch SpringBolt Catch PlungerMagazine Catch Assembly: Improved Milspec Magazine Catch Bar, Enhanced Power Spring, and Improved Button Take Down/ Pivot Pins INFORMATION Kit does NOT include TriggerCompatible lower, trigger and accessories see under this article, accessories NOTICE The beef-up kit must be installed in the lower to maintain function of your GEN-12 upper. If they are not installed then you may have magazines fall out, have the bolt prematurely open, or break a trigger pin during firing. Apply blue thread locker to the screws of the antiwalk pins during installation and torque to 6 in-lbs, and be sure to let cure entirely before shooting.

This Lower parts kit match perfectly with the GEN12 lower and is also compatible with most 308 DPMS gen1 patterned lowers. Kit includes as pictured: Hogue GripPistol grip screwSafety selector springSafety selector detentEnhanced Take Down/ Pivot pinsTake Down/ Pivot pin spring (2x)Take Down/ Pivot pin detent (2x)Safety Selector

  Upgrade your AR-15 lower receiver with the TINCK ARMS Combat Billet Trigger Guard.  Designed for durability, ergonomics, and superior performance. Made from high-quality aluminum, it provides exceptional strength and resistance, while allowing for faster and easier trigger access—even with gloves. The perfect choice for those seeking reliability and comfort in combat applications. Compatible with all standard design AR-15 Mil-Spec Receivers. Features:  Premium Aluminum – Lightweight yet extremely durable construction Ergonomic Design – Ensures quick and easy trigger access Compatibility – Fits a wide range of AR-15 lower receivers Tactical Performance – Designed for fast and efficient operation in all conditions Ideal for use with gloves Standard Wide: 11,0mm No wobbling Simple installation Finish: Matte black hard-coat anodized Mil 8625 Type 3 Class Use a 2mm Hex Key for installation INCLUDES:  1x Billet Combat Trigger Guard 1x Trigger Guard Roll Pin 1x 2mm Hex Set Screw MADE IN SLOVENIA