Handguards

  SPUHR Handguard Cable Organizer Kit, compatible only to SPUHR Interfaces, for example with SPUHR MP5 / HK53 handguards. NOT compatible to M-LOK or KeyMod Interfaces! SPECS  Easy installation Lightweight and robust Set of 3 Nylon cable organizers for use on SPUHR Forends Included M4x10 Torx Screw Kit Length: 32 mm / 1.37" Width: 17 mm / 0.67" Height: 8 mm / 0.32" NOT compatible to M-LOK or KeyMod Interfaces! Compatible accessories, see under this article, accessories   

  SPUHR MP5 / HK33 / HK53 Adjustable 6 Position Drop-in Upgrade Stock. SPECS  Adjustable 6 Position Drop-in Upgrade Stock for MP5, HK33 and HK53 and Clones Easy installation Lightweight and robust Stock adapter and Stock Tube machined from solid billet aircraft aluminum Castle Nut and 2-Point Receiver Endplate made from nitrided steel Stock made from high-strenght polymer Length: 190-270 mm / 7.48-10.62”, Measured from the center of the take-down pin to the rear of the stock Weight: 455 g/16 oz Compatible accessories, see under this article, accessories  The R-315 MP5 Stock Assembly brings the proven design of the R-410 G3 Stock Assembly to the MP5 platform. The R-315 is an updated design of the R-310 MP5 Stock Assembly in that it provides emergency use of the factory iron sights. Using a stock adapter machined from solid billet aircraft aluminum with an integrated buffer, the 6-position adjustable stock is a drop-in replacement of the factory stock and is fully adjustable for length with a non-reciprocating quick-detachable cheek piece, which positions the shooter’s eye in line with optic sights. The check piece can be instantly removed in order to use the factory iron sights if needed.Thanks to the enhanced ergonomics of the stock assembly, recoil management is greatly improved, providing for fast accurate fire even when shooting fully automatic fire. Operation: Install stock assembly using factory HK take down pin. Adjust stock length by pulling down on the rear of the adjustment lever and then slide the stock to the desired length. To remove buttstock from buffer tube, pull down fully on the front of the adjustment lever and then slide stock off the buffer tube. Remove cheek piece by pulling it up and to the rear (pull on the front of the cheek piece). Re-attach cheek piece by sliding it onto top of the stock comb so the rear of the cheek piece grips the comb, then push front of check piece onto the aluminum stock adapter to lock into place.

  SPUHR MP5/HK53 Upgrade Hanguard. SPECS  Lightweight slim profile aluminum forend for MP5/HK53 and Clones Made from single billet of 7000-series aluminum alloy Weight: 92 g/3.3 oz Includes one A-0002 Picatinny Rail as well as two set screws to take up any play between the rear of the rail and the receiver and/or barrel shank Features Spuhr Interfaces on the bottom and the sides for attaching accessories Lower weight than original plastic forend! Sold with 1 x A-0002 Picatinny rail Compatible accessories, see under this article, accessories  The HK roller delayed series of firearms all suffers from far too long stocks. This is especially apparent when it comes to short users and the use of body armor. To make the situation better we have made a new stock for those guns. It´s a 6-position stock assembly with replaceable cheek pieces allowing for different sight solutions. The new stock will make it possible to adjust the length from 180-260 mm / 7.09”-10.24” and also raise the cheek piece and butt plate around 20 mm (0,8”). That way the LOP (Length of Pull) can be adjusted to the current clothing or the current user of the gun. It will make the gun more controllable as the stock is more optimized after the user.  The MP5 Forend is a lightweight modular forend, which follows the same general design as our G3 forend. The R-301 also fit the HK53. The MP5 Top Rail allows the user to attach optics to the MP5.

   SPUHR Sling Swivel Interface, kompatibel zu allen SPUHR® HK MP5 / 417 / G3 / G36 Handguards. Nicht kompatibel zu KeyMod oder M-LOK Interfaces Details/Angebotsumfang: Sling Swivel Interface Includes screws Kompatibles Zubehör siehe unter diesem Artikel, Zubehör.   SPUHR® ist ein Hersteller für hochqualitative Zielfernrohr-Montagesysteme mit Sitz in Schweden, das Unternehmen beliefert hauptsächlich militärische und behördliche Einrichtungen. Sling Swivel Interface For Carabiner and QD Dimensions: 55 mm x 8 mm Weight: 14 g/0.5 oz Screws: Tx20 M4x8 (included) Note: . The A-0109 is designed to attach to a Spuhr Interface®, such as can be found on our HK 417, G3, G36, and MP5 handguards. The A-0109 is NOT designed for use with - nor will it fit - MLOK, KeyMod, or any other third party interface system.