TTI parts

  The 3mm is our low-profile extension for the Staccato/Springfield Prodigy/Atlas/Infinity 9/38 2011 style magazine. Leaving in the factory spring and follower it will be a +1 on a 126, 140 and 170mm magazine. Although it will work on all 2011 magazines, its recommended as a low-profile pad for the 126 magazine to bump it from 17 to 18 rounds. And for the 170mm competition magazine big sticks it bumps it from 26 to 27. If you use our competition thin follower and extra power 13 coil spring it bumps it to 29 and still fits the 170mm USPSA gauge (but will not slide lock on last round fired). The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Magazine NOT included * For the Infinity Magazines: Our base pads will fit all the Infinity magazines and every generation. 9mm/38 – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 23+1 capacity. For Unlimited Division, we recommend the 170mm, the same 3mm extension must be used with our thin competition follower and 13 coil extra power spring to get 29+1 rounds and still fit the USPSA 170mm Gauge. Using a 140mm Magazine with our 7mm extension and our thin competition follower and 11 coil extra power spring will bump the capacity to 24+1. Recommended for the Unlimited Division. If you’re not buying any of this for competition, you can mix and match any of these magazines and pads for different endless combinations. .40SW – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 21+1 capacity. For the .40 Magazines: Staccato Magazines: without changing the spring and follower using our 4mm base pad will bump the capacity from 18 to 20 rounds and fit the 140mm USPSA gauge for limited. With our thin competition follower and 11 coil extra power spring it will hold 21 rounds. (but will not lock the slide to the rear on the last round fired Infinity: 140mm .40SW Magazines, the 3mm base pad and our thin competition follower and 11 coil extra power spring it will hold 21 rounds and still fit the 140mm gauge for USPSA/limited division. (but will not lock the slide to the rear on the last round fired Atlas Magazines: Using our 4mm base pad will allow the magazine to hold 18 rounds with the factory spring and follower. With our thin competition follower and 11 coil extra power spring it will bump the capacity from 18 rounds to 20 rounds. (but will not lock the slide to the rear on the last round fired). NOTE *Due to the variances in mag tube dimensions from different companies and even different generations of mags from the same company, the base pad may require minor fitting to the tube and the back of the lips may need the sharp edges buffed down so the mag will fit the gauge.*MADE IN THE USA

  This Taran Tactical Innovations 7.62x39mm AK base pad is designed to work with PMAG® 30 AK/AKM Gen M3®, PMAG® 30AK/AKM MOE® and PMAG® 30rd AK74 MOE® magazines. This TTI base pad will add 6 extra rounds to the PMAG® 30 AK/AKM Gen M3® and PMAG® 30rd AK74 MOE® magazine and 4/5 rounds (Depending on generation) to PMAG® 30AK/AKM MOE®magazines. This TTI base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI 7.62x39mm PMAG base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Remove the metal insert at the bottom before installation * * Magazine NOT included * PMAG Base Pad For AK 7.62x39mm 30rd AK/AKM Gen 3 M3® and AK74 PMAG® 30rd AK74 MOE® 5.45x39mm TTI FIREPOWER PMAG MAGAZINE EXTENSION: Designed to work with stock spring. Overall weight 3.1oz. Length, 3 inch. Height, 1.5 inch The added overall length of the magazine makes it the ideal height to use as a monopod when shooting from the prone position Patented, proven push-pin design. Easily attaches and detaches from the magazine. No specialty tools, devices, or additional springs required for assembly/disassembly, simply pop off the insert at the bottom of the spring and slide on the extension. One piece design; no small parts to keep track of. Minimal length addition to allow usage while in a prone position. Holds 36+1 rounds on the PMAG® 30 AK/AKM Gen M3® magazine and PMAG® 30rd AK74 MOE® magazine/ Holds 34+1 rounds or 35+1 on the PMAG® 30AK/AKM MOE® magazine (Depending on generation) The added weight helps the magazine drop free easier for faster reloads. CNC machined from billet aluminum. Hard anodized. Made in the USA.

  This Taran Tactical Innovations base pad works on Sig Sauer P320 Full Size 17/21 round 9mm and 14/18 round .40 S&W Full Size Magazine Bodies.  This TTI base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI SIG base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad onto the magazine and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Due to magazine variances, some magazines may require slight modification to fit the 140mm gauge. * * Remove the metal insert at the bottom before installation * * This base pad is compatible with the stock P320 X5 magwell * * Remove the metal insert at the bottom before installation * * NOT compatible with carry size frames * * Magazine NOT included *  TTI FIREPOWER +1 BASE PAD FOR FULL SIZE SIG P320 AND FULL SIZE X5 IS COMPATIBLE WITH:  17 and 21 Round 9mm Magazine 14 and 18 Round 40 S&W Magazine  SIG P320 +1 BASE PAD IS DESIGNED TO WORK WITH STOCK MAGAZINE SPRINGS.  Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized.Made in the USA.

This Taran Tactical Innovations .308 PMAG base pad works on any .308 20 or 25 round PMAG magazine. Compatible accessories see under this article, accessories. This TTI base pad will add 5 extra rounds to a PMAG 20 round magazine and extra 6 rounds in a 25 round PMAG magazine. This TTI base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI .308 PMAG base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. *Remove the metal insert at the bottom before installation* *Will only work on Gen 3 PMAG Magazines* PMAG Base Pad For AR10 .308 TTI Firepower PMAG Magazine Extension Specs: Designed to work with stock spring.Overall weight 4.16oz.Length, 3.5 inch.Patented, proven push-pin design.Easily attaches and detaches from the magazine.No specialty tools, devices, or additional springs required for assembly/disassembly, simply pop off the insert at the bottom of the spring and plastic follower and slide on the extension.One piece design; no small parts to keep track of.Minimal length addition to allow usage while in a prone position.Holds 25+1 rounds on the PMAG20.Holds 31+1 rounds on the PMAG25.The added weight helps the magazine drop free easier for faster reloads.CNC machined from billet aluminum.Hard anodized.Made in the USA.

  This Taran Tactical Innovations base pad works on Sig Sauer P320 Full Size 17/21 round 9mm and 14 round .40 S&W Full Size Magazine Bodies. +10% stronger Magazine Spring included This TTI base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI SIG base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad onto the magazine and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Due to magazine variances, some magazines may require slight modification to fit the 140mm gauge. * * Remove the metal insert at the bottom before installation * * This base pad is compatible with the stock P320 X5 magwell * * Remove the metal insert at the bottom before installation * * NOT compatible with carry size frames * * Magazine NOT included * TTI FIREPOWER +3/5 BASE PAD FOR SIG P320 17/21 ROUND 9MM AND 14 ROUND 40 S&W FULL SIZE MAGAZINE BODIES *Compatible with X5* This Sig P320 +5 includes a 10% stronger spring with purchase Patented proven push pin design. Adds +5 rounds to 9mm. Adds +3 rounds to 40 Cal. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. Made in the USA.

  This Taran Tactical Innovations base pad works on Sig Sauer P320 Full Size 17/21 round 9mm and 14 round .40 S&W Full Size Magazine Bodies. +10% stronger Magazine Spring included This TTI base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI SIG base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad onto the magazine and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Due to magazine variances, some magazines may require slight modification to fit the 140mm gauge. * * Remove the metal insert at the bottom before installation * * This base pad is compatible with the stock P320 X5 magwell * * Remove the metal insert at the bottom before installation * * NOT compatible with carry size frames * * Magazine NOT included * TTI FIREPOWER +3/5 BASE PAD FOR SIG P320 17/21 ROUND 9MM AND 14 ROUND 40 S&W FULL SIZE MAGAZINE BODIES *Compatible with X5* This Sig P320 +5 includes a 10% stronger spring with purchase Patented proven push pin design. Adds +5 rounds to 9mm. Adds +3 rounds to 40 Cal. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. Made in the USA

This Taran Tactical Innovations .223 PMAG base pad works on any .223 Rem 30 or 40 round Gen 3 PMAG magazine. Compatible accessories see under this article, accessories. This TTI base pad will add 5 extra rounds to a PMAG 30 round magazine and extra 6 rounds in a 40 round PMAG magazine. This TTI base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI .223 PMAG base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Remove the metal insert at the bottom before installation * * Will only work on Gen 3 Magpul PMAG Magazines * * Magazine NOT included * PMAG BASE PAD FOR AR .223/5.56 TTI FIREPOWER PMAG MAGAZINE EXTENSION: Designed to work with stock spring.Overall weight 2.1oz.Length, 1 inch.Patented, proven push-pin design.Easily attaches and detaches from the magazine.No specialty tools, devices, or additional springs required for assembly/disassembly, simply pop off the insert at the bottom of the spring and slide on the extension.One piece design; no small parts to keep track of.Minimal length addition to allow usage while in a prone position.Holds 35+1 rounds on the PMAG30.Holds 46+1 rounds on the PMAG40.The added weight helps the magazine drop free easier for faster reloads.CNC machined from billet aluminum.Hard anodized.Made in the USA.

This Taran Tactical Innovations .223 PMAG base pad works on any .223 Rem 30 or 40 round Gen 3 PMAG magazine. Compatible accessories see under this article, accessories. This TTI base pad will add 5 extra rounds to a PMAG 30 round magazine and extra 6 rounds in a 40 round PMAG magazine. This TTI base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI .223 PMAG base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Remove the metal insert at the bottom before installation * * Will only work on Gen 3 Magpul PMAG Magazines * * Magazine NOT included * PMAG BASE PAD FOR AR .223/5.56 TTI FIREPOWER PMAG MAGAZINE EXTENSION: Designed to work with stock spring.Overall weight 2.1oz.Length, 1 inch.Patented, proven push-pin design.Easily attaches and detaches from the magazine.No specialty tools, devices, or additional springs required for assembly/disassembly, simply pop off the insert at the bottom of the spring and slide on the extension.One piece design; no small parts to keep track of.Minimal length addition to allow usage while in a prone position.Holds 35+1 rounds on the PMAG30.Holds 46+1 rounds on the PMAG40.The added weight helps the magazine drop free easier for faster reloads.CNC machined from billet aluminum.Hard anodized.Made in the USA.

The TTI Ultimate Light Speed Black Chrome Silicon Buffer Spring is designed by Taran Butler to achieve the fastest follower up shots and the quickest target to target acquisition possible by eliminating excessive muzzle dip and rearward bounce caused by over powered factory springs. Specs: Also allows the shooter to have a wider variety of shooting 36 to 80 grain bullets with greater reliability.This buffer spring is gear towards more advanced shooters and 3-Gun competitors that use adjustable gas blocks or premium quality barrels that have the smaller diameter gas holes.The TTI Ultimate Light Speed buffer spring works in both A1/A2 length stocks and Carbine M-4 collapsible stocks with Carbine Lenght Buffer Tubes.Combine our buffer spring with the JP Enterprises Low-Mass Recoil Buffer System to achieve the ultimate results.MADE IN THE USA

  The 7mm is our longest extension for the Staccato/Infinity/Springfield Prodigy/Atlas/Infinity/MBX 9/38 2011 style magazine and Bul Armory SAS II Pistols. Although it will work with all 2011 style magazines it is recommended for the 140mm Magazines for Open/Unlimited division and the 126mm because that’s what John Wick will do. On the 140mm magazine, the 7mm extension bumps the capacity from 20 rounds to 22 rounds with the factory spring and follower. For even more added capacity, use our thin competition follower and extra power 11 coil spring for an impressive 24 round capacity (but will not lock the slide to the rear on the last round fired). The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Magazine NOT included * For the Infinity Magazines: Our base pads will fit all the Infinity magazines and every generation. 9mm/38 – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 23+1 capacity. For Unlimited Division, we recommend the 170mm, the same 3mm extension must be used with our thin competition follower and 13 coil extra power spring to get 29+1 rounds and still fit the USPSA 170mm Gauge. Using a 140mm Magazine with our 7mm extension and our thin competition follower and 11 coil extra power spring will bump the capacity to 24+1. Recommended for the Unlimited Division. If you’re not buying any of this for competition, you can mix and match any of these magazines and pads for different endless combinations. .40SW – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 21+1 capacity. For the .40 Magazines: Staccato Magazines: without changing the spring and follower using our 4mm base pad will bump the capacity from 18 to 20 rounds and fit the 140mm USPSA gauge for limited. With our thin competition follower and 11 coil extra power spring it will hold 21 rounds. (but will not lock the slide to the rear on the last round fired Infinity: 140mm .40SW Magazines, the 3mm base pad and our thin competition follower and 11 coil extra power spring it will hold 21 rounds and still fit the 140mm gauge for USPSA/limited division. (but will not lock the slide to the rear on the last round fired Atlas Magazines: Using our 4mm base pad will allow the magazine to hold 18 rounds with the factory spring and follower. With our thin competition follower and 11 coil extra power spring it will bump the capacity from 18 rounds to 20 rounds. (but will not lock the slide to the rear on the last round fired). NOTE *Due to the variances in mag tube dimensions from different companies and even different generations of mags from the same company, the base pad may require minor fitting to the tube and the back of the lips may need the sharp edges buffed down so the mag will fit the gauge.*MADE IN THE USA

  The 4mm is our mid profile extension for the Staccato/Infinity/Springfield Prodigy/Atlas/Infinity 9/38 2011 style magazine. Although it will work on all 2011 style magazines, it is recommended for the 140mm magazine. It brings the capacity up from 20 rounds to 22 rounds with the factory spring and follower and still fits the USPSA 140mm gauge. If you want even more added capacity use our thin competition follower and extra power 11 coil spring to bump the capacity up to 23 rounds (but will not lock the slide to the rear on the last round fired). The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. * Magazine NOT included * For the Infinity Magazines: Our base pads will fit all the Infinity magazines and every generation. 9mm/38 – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 23+1 capacity. For Unlimited Division, we recommend the 170mm, the same 3mm extension must be used with our thin competition follower and 13 coil extra power spring to get 29+1 rounds and still fit the USPSA 170mm Gauge. Using a 140mm Magazine with our 7mm extension and our thin competition follower and 11 coil extra power spring will bump the capacity to 24+1. Recommended for the Unlimited Division. If you’re not buying any of this for competition, you can mix and match any of these magazines and pads for different endless combinations. .40SW – Recommendations for competition magazine guidelines: You must use the 3mm extension with your 140mm magazine tubes in order to fit the 140mm gauge. Using our thin competition follower and 11 coil extra power spring you’ll get 21+1 capacity. For the .40 Magazines: Staccato Magazines: without changing the spring and follower using our 4mm base pad will bump the capacity from 18 to 20 rounds and fit the 140mm USPSA gauge for limited. With our thin competition follower and 11 coil extra power spring it will hold 21 rounds. (but will not lock the slide to the rear on the last round fired Infinity: 140mm .40SW Magazines, the 3mm base pad and our thin competition follower and 11 coil extra power spring it will hold 21 rounds and still fit the 140mm gauge for USPSA/limited division. (but will not lock the slide to the rear on the last round fired Atlas Magazines: Using our 4mm base pad will allow the magazine to hold 18 rounds with the factory spring and follower. With our thin competition follower and 11 coil extra power spring it will bump the capacity from 18 rounds to 20 rounds. (but will not lock the slide to the rear on the last round fired). NOTE *Due to the variances in mag tube dimensions from different companies and even different generations of mags from the same company, the base pad may require minor fitting to the tube and the back of the lips may need the sharp edges buffed down so the mag will fit the gauge.*MADE IN THE USA

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 31 and 33 round OEM Magazines, + 10% stronger Magazine Spring included. Holds 34 rounds of 9mm in 31 round Magazine (+1 round extra in Chamber). Holds 34 rounds of 9mm in 33 round Magazine (+1 round extra in Chamber). GLOCK 9MM +3 PCC ** Remove the plastic insert at the bottom before installation ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES! ** ** WILL NOT WORK WITH GLOCK 17 OR 19 MAGAZINES! ** ** WILL NOT work with KCI or ETS magazines ** ** GLOCK OEM Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK. The +3 Base Pad includes a +10% stronger spring with purchase. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized.Made in the USA Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. Weighs 1.6 OZ This base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This GLOCK base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA.

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 31 and 33 round OEM Magazines, + 10% stronger Magazine Spring included. Holds 34 rounds of 9mm in 31 round Magazine (+1 round extra in Chamber). Holds 34 rounds of 9mm in 33 round Magazine (+1 round extra in Chamber). GLOCK 9MM +3 PCC ** Remove the plastic insert at the bottom before installation ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES! ** ** WILL NOT WORK WITH GLOCK 17 OR 19 MAGAZINES! ** ** WILL NOT work with KCI or ETS magazines ** ** GLOCK OEM Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK. The +3 Base Pad includes a +10% stronger spring with purchase. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized.Made in the USA. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. Weighs 1.6 OZ This base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This GLOCK base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA.

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 19/23, +4/5 rounds more, Magazine Spring included. Holds 20 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 17 rounds of 40S&W in Magazine (+1 round extra in Chamber).  GLOCK 19/23 +4/5 ** Remove the metal insert at the bottom before installation ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES! ** ** Will work with ETS 15 Round 9mm magazines ** ** GLOCK Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK. The +4/5 Base Pad comes with a +10% stronger spring. Overall weight 1.5oz. Length, 1 1/2 inch front side, 3/4 inch on back side. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Ideal for full size magazines. Holds 17 rounds of 40S&W in Magazine (+1 round extra in Chamber).  Holds 20 rounds of 9mm in Magazine (+1 round extra in Chamber). The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Made in the USA. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. The Taran Tactical Innovations GLOCK +4/5 base pad works on GLOCK models 19/23. This base pad will add 5 extra rounds in 9mm and 4 extra rounds in 40 Caliber to the magazine. This base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This GLOCK base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA.

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 19/23, +4/5 rounds more, Magazine Spring included. Holds 20 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 17 rounds of 40S&W in Magazine (+1 round extra in Chamber).  GLOCK 19/23 +4/5 ** Remove the metal insert at the bottom before installation ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES! ** ** Will work with ETS 15 Round 9mm magazines ** ** GLOCK Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK. The +4/5 Base Pad comes with a +10% stronger spring. Overall weight 1.5oz. Length, 1 1/2 inch front side, 3/4 inch on back side. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Ideal for full size magazines. Holds 17 rounds of 40S&W in Magazine (+1 round extra in Chamber).  Holds 20 rounds of 9mm in Magazine (+1 round extra in Chamber). The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Made in the USA. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. The Taran Tactical Innovations GLOCK +4/5 base pad works on GLOCK models 19/23. This base pad will add 5 extra rounds in 9mm and 4 extra rounds in 40 Caliber to the magazine. This base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This GLOCK base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA.

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 19/23, +2/3 rounds more, Magazine Spring included. Holds 18 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 15 rounds of 40S&W in Magazine (+1 round extra in Chamber).  GLOCK 19/23 +2/3 ** Remove the metal insert at the bottom before installation ** ** This product will ONLY work on Glock 19 and Glock 23 firearms! ** ** This product will ONLY work on the Compact 9mm and .40 cal Glock OEM magazines! ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES, ASIDE FROM OUR +0 BASE PADS ** ** GLOCK Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK OEM MAGAZINES. Overall weight 0.8oz. Length, 1/2 inch. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Works only on high-cap double stacked GLOCK OEM magazines. Holds 15+1 rounds of 40S&W. Holds 18+1 rounds of 9mm. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized.MADE IN THE USA Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. The Taran Tactical Innovations GLOCK +2/3 base pad works on GLOCK models 19/23. This base pad will add 3 extra rounds in 9mm and 2 extra rounds in 40 Caliber to the magazine. This base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI GLOCK base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad onto the magazine and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA.

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 19/23, +2/3 rounds more, Magazine Spring included. Holds 18 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 15 rounds of 40S&W in Magazine (+1 round extra in Chamber).  GLOCK 19/23 +2/3 ** Remove the metal insert at the bottom before installation ** ** This product will ONLY work on Glock 19 and Glock 23 firearms! ** ** This product will ONLY work on the Compact 9mm and .40 cal Glock OEM magazines! ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES, ASIDE FROM OUR +0 BASE PADS ** ** GLOCK Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK OEM MAGAZINES. Overall weight 0.8oz. Length, 1/2 inch. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Works only on high-cap double stacked GLOCK OEM magazines. Holds 15+1 rounds of 40S&W. Holds 18+1 rounds of 9mm. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized.MADE IN THE USA Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. The Taran Tactical Innovations GLOCK +2/3 base pad works on GLOCK models 19/23. This base pad will add 3 extra rounds in 9mm and 2 extra rounds in 40 Caliber to the magazine. This base pad does add a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI GLOCK base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad onto the magazine and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA.

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 17/19X/22/34/35/45 +5/6 rounds more, +10% stronger spring included. Holds 23 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 20 rounds of 40S&W in Magazine (+1 round extra in Chamber).  Disclaimer: Due to variances with Glock magazines, we recommend checking your magazines in a mag gauge prior to competitions to ensure proper fitment/specifications. Doing this will also help avoid being bumped to another division. We recommend contacting your local match director preemptively to inquire about specific requirements as each match director may have different guidelines and regulations ** Both extensions will compatible with Glock 45 firearms as well as Glock 19X firearms. Product has only been tested out with Glock OEM magazines ** ** Remove the OEM polymer insert at the bottom before installation ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES ** ** Will NOT work on GLOCK 19 ** ** GLOCK Magazine NOT included ** ** Will work with ETS 17 round 9mm magazines ** TTI FIREPOWER BASE PAD KIT FOR GLOCK The +5/6 Base Pad includes a +10% stronger spring with purchase. Overall weight 1.6oz. Length, 1 1/2 inch front side, 3/4 inch on back side. Will work on all full size double stacked GLOCKs. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Ideal for full size magazines. Holds 20+1 rounds of 40S&W. Holds 23+1 rounds of 9mm. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. MADE IN THE USA

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 17/19X/22/34/35/45 +5/6 rounds more, +10% stronger spring included. Holds 23 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 20 rounds of 40S&W in Magazine (+1 round extra in Chamber).  Disclaimer: Due to variances with Glock magazines, we recommend checking your magazines in a mag gauge prior to competitions to ensure proper fitment/specifications. Doing this will also help avoid being bumped to another division. We recommend contacting your local match director preemptively to inquire about specific requirements as each match director may have different guidelines and regulations ** Both extensions will compatible with Glock 45 firearms as well as Glock 19X firearms. Product has only been tested out with Glock OEM magazines ** ** Remove the OEM polymer insert at the bottom before installation ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES ** ** Will NOT work on GLOCK 19 ** ** GLOCK Magazine NOT included ** ** Will work with ETS 17 round 9mm magazines ** TTI FIREPOWER BASE PAD KIT FOR GLOCK The +5/6 Base Pad includes a +10% stronger spring with purchase. Overall weight 1.6oz. Length, 1 1/2 inch front side, 3/4 inch on back side. Will work on all full size double stacked GLOCKs. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Ideal for full size magazines. Holds 20+1 rounds of 40S&W. Holds 23+1 rounds of 9mm. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler.MADE IN THE USA

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 17/19X/22/34/35/45 +5/6 rounds more, +10% stronger spring included. Holds 23 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 20 rounds of 40S&W in Magazine (+1 round extra in Chamber).  Disclaimer: Due to variances with Glock magazines, we recommend checking your magazines in a mag gauge prior to competitions to ensure proper fitment/specifications. Doing this will also help avoid being bumped to another division. We recommend contacting your local match director preemptively to inquire about specific requirements as each match director may have different guidelines and regulations ** Both extensions will compatible with Glock 45 firearms as well as Glock 19X firearms. Product has only been tested out with Glock OEM magazines ** ** Remove the OEM polymer insert at the bottom before installation ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES ** ** Will NOT work on GLOCK 19 ** ** GLOCK Magazine NOT included ** ** Will work with ETS 17 round 9mm magazines ** TTI FIREPOWER BASE PAD KIT FOR GLOCK The +5/6 Base Pad includes a +10% stronger spring with purchase. Overall weight 1.6oz. Length, 1 1/2 inch front side, 3/4 inch on back side. Will work on all full size double stacked GLOCKs. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Ideal for full size magazines. Holds 20+1 rounds of 40S&W. Holds 23+1 rounds of 9mm. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. MADE IN THE USA

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 17/19X/22/34/35/45 +3/4 rounds more. Holds 21 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 18 rounds of 40S&W in Magazine (+1 round extra in Chamber).  ** Both extensions will compatible with Glock 45 firearms as well as Glock 19X firearms. Product has only been tested out with Glock OEM magazines ** ** Remove the OEM polymer insert at the bottom before installation ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES ** ** Will NOT work on GLOCK 19 ** ** GLOCK Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK Designed to work with stock magazine spring. Will work on all full size double stacked GLOCKs. Overall weight 0.8oz. Length, 1/2 inch. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Works only on high-cap double stacked GLOCK OEM magazines. Holds 18+1 rounds of 40S&W. Holds 21+1 rounds of 9mm. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. MADE IN THE USA

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 17/19X/22/34/35/45 +3/4 rounds more. Holds 21 rounds of 9mm in Magazine (+1 round extra in Chamber). Holds 18 rounds of 40S&W in Magazine (+1 round extra in Chamber).  ** Both extensions will compatible with Glock 45 firearms as well as Glock 19X firearms. Product has only been tested out with Glock OEM magazines ** ** Remove the OEM polymer insert at the bottom before installation ** ** Will not function with early generation Glock mags that have u-notch cut feed lips ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES ** ** Will NOT work on GLOCK 19 ** ** GLOCK Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK Designed to work with stock magazine spring. Will work on all full size double stacked GLOCKs. Overall weight 0.8oz. Length, 1/2 inch. Patented proven push pin design. Super easy to attach and detach from the magazine. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Works only on high-cap double stacked GLOCK OEM magazines. Holds 18+1 rounds of 40S&W. Holds 21+1 rounds of 9mm. The added weight helps the magazine drop free easily for faster reloads. CNC machined from billet aluminum. Hard Anodized. Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. MADE IN THE USA

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 21/41, +4 rounds more, 10% stronger Magazine Spring included. Holds 17 rounds of .45 ACP in Magazine (+1 round extra in Chamber). GLOCK 21/41 ** Remove the polymer insert at the bottom before installation ** ** Will NOT work with 10mm ammo. Our extensions are designed to work specifically with their intended magazine, the slightest off-angle may cause failure to feed or other malfunctions ** ** Will NOT function with early generation Glock mags that have u-notch cut feed lips. ** ** WILL NOT WORK WITH SUBCOMPACT MAGAZINES (G30/G30S/G30SF/G36) ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES ** ** GLOCK Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK OEM MAGAZINES. +10% stronger spring included. Overall weight 1.7oz. Length, 1 1/2 inch front side, 3/4 inch on back side. Patented proven push pin design. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Ideal for full size magazines. Holds 17+1 rounds of .45ACP. The added weight helps the magazine drop free easier for faster reloads. CNC machined from billet aluminum. Hard Anodized.MADE IN THE USA Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. This Taran Tactical Innovations GLOCK base pad works on GLOCK models 21/41. This TTI base pad will add 4 extra rounds of .45 ACP to the magazine. This base pad does adds a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI GLOCK base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA.

  Taran Tactical Innovations Firepower Base Pad Kit for Glock 21/41, +4 rounds more, 10% stronger Magazine Spring included. Holds 17 rounds of .45 ACP in Magazine (+1 round extra in Chamber). GLOCK 21/41 ** Remove the polymer insert at the bottom before installation ** ** Will NOT work with 10mm ammo. Our extensions are designed to work specifically with their intended magazine, the slightest off-angle may cause failure to feed or other malfunctions ** ** Will NOT function with early generation Glock mags that have u-notch cut feed lips. ** ** WILL NOT WORK WITH SUBCOMPACT MAGAZINES (G30/G30S/G30SF/G36) ** ** WILL NOT WORK WITH 10 ROUND MAGAZINES ** ** GLOCK Magazine NOT included ** TTI FIREPOWER BASE PAD KIT FOR GLOCK OEM MAGAZINES. +10% stronger spring included. Overall weight 1.7oz. Length, 1 1/2 inch front side, 3/4 inch on back side. Patented proven push pin design. No specialty tools or devices required to disassemble. One piece design, no extra parts to possibly lose during disassembly. Fits the USPSA 140mm gauge. Ideal for full size magazines. Holds 17+1 rounds of .45ACP. The added weight helps the magazine drop free easier for faster reloads. CNC machined from billet aluminum. Hard Anodized.MADE IN THE USA Used and endorsed by World and National Champions Bob Vogel, the GLOCK Shooting Team, Randi Rogers, Allie Barrett, and of course Taran Butler. The pin set screws are set with Loctite® at the specific tension we recommend, and will generally never need an adjustment. Tightening the base pad screw is not recommended and may be difficult because the screw is set with Loctite®; trying to force the set screw to turn could result in stripping the screw. We do not warranty base pads for stripped heads on set screws or pins lost in result of tampering with the set screw. This Taran Tactical Innovations GLOCK base pad works on GLOCK models 21/41. This TTI base pad will add 4 extra rounds of .45 ACP to the magazine. This base pad does adds a little extra weight to the magazine which helps the empty mag drop free easier for faster reloads. This TTI GLOCK base pad, just like all of our base pads, is designed to give you the edge over your adversaries. We use our patented push pin design to lock the base pad to the magazine, which makes for easy field stripping and cleaning your magazines between stages. Just push down the pin, slide the base pad on and push the pin up to lock the base pad onto the magazine. Our one piece design is great because there are no extra parts or tools needed to attach the base pad to your magazine. The base pad itself is machined out of billet aluminum and is hard anodized to ensure durable long lasting color. All machining and manufacturing is done in the USA.